↑Back to top
China, Europe, US · EV traction motors PEM Chair, RWTH Aachen University, Energies, Nov 6, 2026

RWTH Aachen University benchmarks 115 e-motors: Chinese and European architectures are similar, but housing and busbar materials differ

RWTH Aachen University's Chair of Production Engineering of E-Mobility Components (PEM) has published a benchmarking study in the journal Energies. The sample covers 115 traction motors from 80 electric vehicles of model years 2019 to 2025, mostly models for the Chinese market, compared against European and American motors the institute studied in 2025. The paper concludes that e-drives from the three regions show no fundamental differences in housing structure, stator and rotor geometry, or newer cooling concepts; the differences lie in material choices and component design details.

Energies 19(21), 5324 · 2026-11-06 PEM press release · 2026-11-10 e+i 142, 312–345 · 2025-07-15 electrive · 2026-11-11
Traction motors in the sample
0 units
From 80 EV models, model years 2019 to 2025
Average peak power density of permanent magnet synchronous motors
0kW/kg
2024–2025 model years; 1.68 in 2019
Highest motor speed in the sample
0 rpm
2020–2022 model years mostly 8,000 to 17,000
Share of inverters using silicon carbide
0%
16 of 44 units, 2024–2025 model years; previously 17%
01 / study sample

80 models, 115 motors, incl. BEV, EREV and PHEV

Data come from MOVO Autodatas' DARWIN benchmarking database, PEM's own teardowns and public sources. In the selected EREV and PHEV models, the electric drive does not share a housing with the combustion engine. Power density is calculated on the weight of the entire drive unit, including power electronics, reduction gear and housing, but excluding half-shafts.

Close-up of the motor stator end: flat-wire (hairpin) windings, three-phase copper terminals and aluminium housing
Stator end of the NIO ET7 drive motor, showing hairpin windings and three-phase terminals. Image: PEM RWTH Aachen
Sample overview: 115 traction motors from 80 vehicles, model years 2019–2025; average drive unit weight 87.26 kg
Paper, sections 4 and 5.1.3 · weight covers the entire drive unit
Drive motor
115 units
Only permanent-magnet synchronous and induction motors
Model
80 models
BEV, EREV, PHEV
Model year
2019–2025
Mainly the Chinese market
Average drive unit weight
87.26 kg
Heaviest 151.67 kg, lightest 42 kg
Average reduction ratio
10.56
Max 15.02, min 3.67
Max. e-drive voltage
945 V
2020 model year: 350 to 400 V
Source: Drexler et al., Energies 2026, 19(21), 5324
Samples in the two PEM benchmarking studies: 48 motors from 31 vehicles in 2025; 115 motors from 80 vehicles in 2026
Models, units · 2025 study covers model years 2018–2023, mainly European and US models; 2026 study covers model years 2019–2025, mainly China-market models
Source: e+i Elektrotechnik und Informationstechnik 142, 312–345 (2025-07-15); Energies 19(21), 5324 (2026-11-06)
▸ The new study uses the previous study's analytical framework; the China–Europe–US comparison combines the two samples, and the number of motors is about 2.4 times that of the previous study.
02 / Materials and components

Chinese models mostly use magnesium-alloy housings and powder-coated busbars; European models mostly use aluminium housings and polymer busbar assemblies

The paper cites housing material and busbar design as two examples of regional differences; another is motor type: the China-focused sample contains no electrically excited synchronous motors. The authors note that the study can identify differences but not determine their causes, and the explanations offered are hypotheses.

Differences between Chinese and European e-drives listed in the paper: housing material, busbar insulation, motor type
The China column reflects observations from this sample; the Europe column is a comparison with PEM's 2025 study
ItemChinese modelsEuropean models
Housings and structural partsSeveral automakers have switched to magnesium alloy in recent yearsAluminum alloy retained
Housing weightApprox. 20%–30% lighter than aluminum housingsBaseline
Stator busbarMostly busbars with powder-coat insulationMostly assemblies with multiple copper busbars embedded in polymer parts; more complex structure
Motor typePermanent-magnet synchronous, induction; no electrically excited synchronousBMW and Renault have mass-produced electrically excited synchronous motors for years
Common groundNo fundamental differences in housing structure, stator and rotor geometry or new cooling designs. Thinner electrical steel laminations, higher speeds and finer conductor cross-sections appear in all three regions
Possible causes cited in the paperDistribution of raw material reserves and processing industries, labour costs, environmental and regulatory requirements. The paper says these are assumptions
Magnesium supply97% of the EU's magnesium comes from China (European Commission figure, period not specified)
Source: Energies 19(21), 5324, Sections 5.1.1, 5.2.2 and 6. Magnesium alloy weight savings are figures cited in the paper from the literature; for magnesium supply, see the European Commission's critical raw materials page.
▸ The paper notes that magnesium alloys were long held back by casting processes and corrosion resistance; new formulations containing titanium, zinc or tin, along with semi-solid casting, have improved both.
03 / power density and speed

Average peak power density of PMSMs: 1.68 kW/kg in 2019, 2.43 kW/kg for 2024–2025 model years

The paper argues that downsizing motors by raising speed is the main way to increase power density. In the sample, maximum speed, reduction ratio and power density all rose together; stator inner and outer diameters shrank by an average of 10 to 12 mm, rotors lost about 2.3 kg on average, and the effective core stack length was only slightly shorter.

Average peak power density of PMSMs: 1.68 in 2019, 2.43 for 2024–2025 model years, 2.7 kW/kg for 2025 model year
kW/kg, based on the weight of the full drive unit · Average per model year within the sample
Source: Energies 19(21), 5324, Section 5.1.3
▸ The average for model years 2024–2025 is about 145% of the 2019 level, an increase of about 45%.
Motors with the highest peak power density in the sample: NIO ET9 rear motor 4.24 kW/kg, BYD Tang L rear motor 4.08 kW/kg
kW/kg · Blue: permanent magnet synchronous motors; grey: induction motors; vertical line: PMSM average of 2.43 for 2024–2025 model years
Source: Energies 19(21), 5324, Section 5.1.3
▸ The induction motor with the highest power density is the front motor of the NIO ET9, at 2.62 kW/kg; the Voyah FREE's front and rear induction motors reach 2.61 kW/kg.
Maximum motor speed: 8,000 to 17,000 rpm for model years 2020–2022; 14,500 to 23,000 rpm from 2023, peaking at 30,500 rpm
rpm · The range from 2023 excludes the BYD Tang L rear motor, shown separately as a diamond
Source: Energies 19(21), 5324, Section 5.2.1
▸ The paper says that since 2023 the width of the speed range has changed little, with the whole range shifting upwards. The low end is the front motor of a SAIC Motor model and the high end the BYD Sealion 07 EV, followed by several Chery models at 22,000 rpm.
Average reduction ratio: MY 2019–2021 9.45, MY 2024–2025 11.48; full-sample minimum 3.67, maximum 15.02
Reduction ratio, dimensionless · Blue dots are averages for the two periods; grey dots are full-sample average, minimum and maximum
Source: Energies 19(21), 5324, Section 5.2.1
▸ The Tesla Cybertruck has the highest reduction ratio and the Great Wall Ora Good Cat the lowest; the averages for the two periods differ by about 21.5%.
Three power densities, before and after: PM peak 1.68→2.43, PM continuous 0.69→1.00, induction peak 1.96→2.19 kW/kg
kW/kg · The permanent-magnet peak series starts in 2019 and the other two start with 2020–2022 model years; all three end with 2024–2025 model years
Source: Energies 19(21), 5324, Section 5.1.3
▸ Data on continuous power density of induction motors are insufficient, and the paper gives no figure.
Speed and reduction ratio of two motors: BYD Tang L rear motor 30,500 rpm, 10.9; Volkswagen ID.3 16,000 rpm, 11.5
The paper uses this comparison to show that higher speeds are not necessarily used to downsize the motor
ItemBYD Tang L rear motorVolkswagen ID.3
Max speed30,500 rpm16,000 rpm
Gear ratio10.911.5
Peak power density4.08 kW/kg—
Interpretation of the paperThe Tang L's rear motor only gains a higher top speed, with no upward shift in the base (corner) speed; the extra rpm goes toward a higher vehicle top speed
Source: Energies 19(21), 5324, Sections 5.1.3 and 5.2.1
▸ The Tang L rear motor's maximum speed is about 1.9 times that of the ID.3, yet its reduction ratio is lower.
04 / cooling, integration and controls

Model years 2019–2021 almost all used water-jacket cooling; direct oil cooling has become more common since 2024

Oil flows directly over the core laminations of the rotor and stator, raising sealing requirements. The paper suggests this may be why bonded laminations are becoming more common while welded and interlocked laminations are declining. Higher on-board voltages and wider use of silicon carbide devices are also increasing demands on insulation systems.

Share of inverters using silicon carbide: 4 of 23 for model years 2022–2023, 16 of 44 for model years 2024–2025
Each square represents 1% of inverters · blue = silicon carbide inverters, the rest use silicon devices
17% 2022–2023 model years
36% 2024–2025 model years
Source: Energies 19(21), 5324, Sections 5.2.5 and 6
▸ The share in the later period is about 2.1 times that of the earlier period; the highest e-drive voltage in the sample is 945 V.
Changes in cooling and manufacturing: from water jackets to direct oil cooling, from welded to bonded laminations
Summary of Sections 5.2.2 to 5.2.4 and Section 6 of the paper
Item2019–2021 model years2024–2025 model years
CoolingAlmost all water jacketsGrowing use of oil splash-spray cooling combined with direct oil cooling of the rotor, stator laminations and winding end turns
Housing integrationMostly low integration, with multi-section housingsHighly integrated designs dominate from 2022, with power electronics housed in the drive unit casing
Silicon steel lamination thicknessThicker0.25 mm becomes standard
Stator windingHairpin windings increasingly common from 2021–2022Mainly flat-wire U-shaped hairpins from 2024
Lamination fixingWelding, interlockingMore bonded laminations
Source: Energies 19(21), 5324
▸ Round-wire windings are still mainly used in induction motors serving as auxiliary drives; continuous wave windings appear only in a few high-performance e-drives.
2019 to 2026: changes in e-drive design in the sample and publication dates of the two studies
Model year vs. paper publication date · model years reflect the paper's sample, not industry statistics
2019–2021 model years
Water-jacket cooling, low-integration housing
Average peak power density of PMSMs in 2019 was 1.68 kW/kg, with an average reduction ratio of 9.45.
From model year 2022
Highly integrated drive units make up the majority
Motor, reducer and inverter housings integrated into one; hairpin windings increasingly common.
From model year 2023
Maximum speeds shifting higher overall
The range shifts from 8,000–17,000 rpm to 14,500–23,000 rpm.
2024–2025 model years
Direct oil cooling, 0.25 mm silicon steel laminations, U-shaped hairpin flat wire
Permanent-magnet synchronous motors: average peak power density 2.43 kW/kg, average reduction ratio 11.48, silicon carbide share 36%.
Jul 15, 2025
An earlier PEM benchmarking study
31 vehicles and 48 motors from model years 2018 to 2023, mostly European and US models.
Nov 6, 2026
The study was published in Energies
80 models, 115 motors, mainly for the Chinese market; PEM press release, Nov 10.
Data quick reference

Definitions and sources for figures on this page

FiguresScopeSource
115 units; 80 modelsTraction motors and models on EVs of model years 2019–2025, including BEV, EREV and PHEVEnergies 19(21), 5324, Section 4
48 units; 31 modelsSample from PEM's previous study, model years 2018–2023e+i 142, 312–345 abstract
20%–30%Weight saving of magnesium alloy housings vs. conventional aluminium housings, from literature cited in the paperEnergies 19(21), 5324, Section 5.1.1
1.68; 2.43; 2.7 kW/kgAverage peak power density of PMSMs: 2019, MY2024–2025, MY2025; based on total drive unit weightIbid., section 5.1.3
4.24; 4.08; 3.46 kW/kgPeak power density of the NIO ET9 rear motor, BYD Tang L rear motor and Onvo L60Ibid., section 5.1.3
8,000–17,000; 30,500 rpmMain maximum-speed range for MY 2020–2022; sample maximumIbid., section 5.2.1
9.45;11.48Average reduction ratio, 2019–2021 model years vs 2024–2025 model yearsIbid., section 5.2.1
0.25 mmStandard lamination thickness for model years 2024–2025Ibid., section 6
17%;36%Share of analysed inverters using silicon carbide: 4 of 23 and 16 of 44Ibid., section 6
10–12 mm; 2.3 kgAverage reduction in stator inner and outer diameters; average rotor weight reductionIbid., section 6
Source: see each row in the table · Paper data from the DARWIN database, PEM teardowns and public sources · Research funded by the German Federal Ministry for Economic Affairs and Energy